IEI Technology ISP-9652/9602 User Manual Download Page 100

Page: 100 / 119

ISP-9652/9602 User Manual

Page 88

Boots Graphics Adapter [PEG/PCI]

Use the

Boots Graphics Adapter

option to select the graphics controller used as the

primary boot device. Select either an integrated graphics controller (IGD) or a combination

of PCI graphics controller, a PCI express (PEG) controller or an IGD. Configuration

options are listed below:

IGD

EFAULT

PCI/IGD

PEG/IGD

Internal Graphics Mode Select [Enable, 8 MB]

Use the

Internal Graphic Mode Select

option to specify the amount of system memory

that can be used by the internal graphics device.

Disable

Enable, 8 MB

EFAULT

8 MB of memory used by internal graphics device

5.7.2 Southbridge Configuration

Use the

Southbridge Configuration

menu (

BIOS Menu 17

) to configure the Southbridge

chipset.

Summary of Contents for ISP-9652/9602
























































































































Search results

Summary of Contents for ISP-9652/9602

Reviews:

Brands by name

Popular brands

IEI Technology ISP-9652/9602, User Manual

Search results

Summary of Contents for ISP-9652/9602

Reviews:

Brands by name

Popular brands