manualshive.com logo in svg

IEI Technology ISP-9652/9602, User Manual

Share
Download
IEI Technology ISP-9652/9602 User Manual Download Page 60

 

 

ISP-9652/9602 User Manual

Page 48 

 

Figure 4-10: SATA Drive Cable Connection 

Step 10: 

Connect the cable to the SATA disk

. Connect the connector on the other end 

of the cable to the connector at the back of the SATA drive. See 

4

Figure 4-12

. 

Step 10:

 

4.7.3 Single RS-232 Cable (w/o Bracket) 

The single RS-232 cable consists of one serial port connector attached to a serial 

communications cable that is then attached to a D-sub 9 male connector. To install the 

single RS-232 cable, please follow the steps below. 

Step 11: 

Locate the connector

. The location of the RS-232 connector is shown in 

Chapter 3

. 

Step 12: 

Insert the cable connector

. Insert the connector into the serial port box header. 

See Figure 4-11. A key on the front of the cable connectors ensures the 

connector can only be installed in one direction. 

Summary of Contents for ISP-9652/9602
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands