IEI Technology ISP-9652/9602 User Manual Download Page 105

Page: 105 / 119

ISP-9652/9602 User Manual

Page 93

USB 2.0 Controller [Enabled]..............................................................................................76

Legacy USB Support [Enabled]..........................................................................................77

USB2.0 Controller Mode [HiSpeed] ....................................................................................77

Power Management/APM [Enabled]...................................................................................78

Power Button Mode [On/Off]...............................................................................................78

Resume on Ring [Disabled] ................................................................................................79

Resume On RTC Alarm [Disabled] .....................................................................................79

Resume on PCI-Express WAKE# [Enabled]......................................................................79

IRQ# [Available] ...................................................................................................................80

DMA Channel# [Available] ..................................................................................................81

Reserved Memory Size [Disabled] .....................................................................................82

Quick Boot [Enabled] ..........................................................................................................83

Quiet Boot [Enabled] ...........................................................................................................83

AddOn ROM Display Mode [Force BIOS] ..........................................................................83

Bootup Num-Lock [On] .......................................................................................................84

Boot From LAN Support (82574L) [Disabled] ...................................................................84

Change Supervisor Password ............................................................................................85

Change User Password.......................................................................................................85

Memory Remap Feature [Enabled].....................................................................................87

Memory Hole [Disabled] ......................................................................................................87

Boots Graphics Adapter [PEG/PCI] ...................................................................................88

Internal Graphics Mode Select [Enable, 8 MB] .................................................................88

Spread Spectrum [Disabled]...............................................................................................89

Save Changes and Exit .......................................................................................................90

Discard Changes and Exit...................................................................................................90

Discard Changes..................................................................................................................90

Load Optimal Defaults.........................................................................................................90

Load Failsafe Defaults.........................................................................................................90

Summary of Contents for ISP-9652/9602
























































































































Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands

IEI Technology ISP-9652/9602, User Manual

Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands