manualshive.com logo in svg

IEI Technology ISP-9652/9602, User Manual

Share
Download
IEI Technology ISP-9652/9602 User Manual Download Page 62

 

 

ISP-9652/9602 User Manual

Page 50 

4.7.4 USB Cable (Four Port)   

Four port USB 2.0 cables can be separately purchased from IEI. To install a four port USB 

cable onto the ISP-9652/9602, please follow the steps below. 

Step 1: 

Locate the connectors

. The locations of the USB connectors are shown in 

Chapter 4

. 

 WARNING: 

If the USB pins are not properly aligned, the USB device can burn out. 

Step 2: 

Align the connectors

. Each cable has two connectors. Correctly align pin 1on 

each cable connector with pin 1 on the ISP-9652/9602 USB connectors. 

Step 3: 

Insert the cable connectors

.

 

Once the cable connectors are properly aligned 

with the USB connectors on the ISP-9652/9602, connect the cable connectors 

to the on-board connectors. See Figure 4-13. 

 

Figure 4-13: Four Port USB Cable Connection 

Summary of Contents for ISP-9652/9602
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands