IEI Technology ISP-9652/9602 User Manual Download Page 88

Page: 88 / 119

ISP-9652/9602 User Manual

Page 76

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Power

Exit

USB Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Module Version – 2.24.3-13.4

USB Devices Enabled:
None

USB Functions

[Enabled]

USB 2.0 Controller

[Enabled]

Legacy USB Support

[Enabled]

USB 2.0 Controller Mode

[HiSpeed]

Enables USB host
controllers

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 9: USB Configuration

USB Configuration

The

USB Configuration

field shows the system USB configuration. The items listed are:

Module Version: x.xxxxx.xxxxx

USB Devices Enabled

The

USB Devices Enabled

field lists the USB devices that are enabled on the system

USB Function [Enabled]

Use the

USB Function

BIOS option to enable or disable USB function support.

Disabled

USB function support disabled

Enabled D

EFAULT

USB function support enabled

USB 2.0 Controller [Enabled]

Use the

USB 2.0 Controller

BIOS option is enabled.

Summary of Contents for ISP-9652/9602
























































































































Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands

IEI Technology ISP-9652/9602, User Manual

Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands