IEI Technology ISP-9652/9602 User Manual Download Page 84

Page: 84 / 119

ISP-9652/9602 User Manual

Page 72

PWM Maximum Mode: 127

Slope PWM [1 PWM]

A bigger value will increase the fan speed in big amounts. A smaller value will increase the

speed more gradually.

PWM

CPU Fan PWM Control [070]

This value specifies the speed of the fan.

PWM Minimum Mode: 0

PWM Maximum Mode: 127

H/W Health Function [Enabled]

Use the

H/W Health Function

to enable the monitoring of the system environmental

parameters.

Disabled

Disables the health monitoring function

Enabled D

EFAULT

Enables the health monitoring function

Hardware Health Monitoring

The following system parameters and values are shown. The system parameters that are

monitored are:

System

Temperatures:

CPU Temperature

Summary of Contents for ISP-9652/9602
























































































































Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands

IEI Technology ISP-9652/9602, User Manual

Search results

Summary of Contents for ISP-9652/9602

Reviews:

Related manuals for ISP-9652/9602

Brands by name

Popular brands