IEI Technology IMBA-8654 User Manual Download

Page: 104 / 242

IMBA-8654 Motherboard

Page 86

Step 4:

Orientate the CPU properly. Make sure the IHS (Integrated Heat Sink) side is

facing upward.

Step 5:

Correctly position the CPU. Match the Pin 1 mark with the cut edge on the CPU

socket.

Step 6:

Align the CPU pins. Locate pin 1 and the two orientation notches on the CPU.

Carefully match the two orientation notches on the CPU with the socket

alignment keys.

Step 7:

Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are

properly aligned, the CPU should slide into the CPU socket smoothly. See

Figure 5-4

Figure 5-4: Insert the LGA775 CPU

Step 8:

Close the CPU socket. Close the load plate and engage the load lever by

pushing it back to its original position. Secure the load lever under the retention

tab on the side of CPU socket.

Step 9:

Connect the CPU 12V cable to the 12After the cooling kit is installed connect the

CPU cable to the CPU 12V power connector.

Step 0:

Summary of Contents for IMBA-8654



















































































































































































































































Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands

IEI Technology IMBA-8654, User Manual

Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands