IEI Technology IMBA-8654 User Manual Download

Page: 160 / 242

IMBA-8654 Motherboard

Page 142

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB 2.0 Controller [Enabled]

Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller

Disabled

USB 2.0 controller disabled

Enabled D

EFAULT

USB 2.0 controller enabled

USB 2.0 Controller Mode [HiSpeed]

The

USB 2.0 Controller Mode

BIOS option sets the speed of the USB 2.0 controller.

FullSpeed

The controller is capable of operating at full speed

(12Mbits/second)

HiSpeed D

EFAULT

The controller is capable of operating at high speed

(480Mbits/second)

BIOS EHCI Handoff [Enabled]

Use the

BIOS EHCI Handoff

option for systems running OSes that do not have EHCI

hand-off support. The EHCI ownership change is managed by the EHCI driver.

Disabled

Systems with OSes that do not support EHCI can

use the EHCI handoff functionality.

Enabled D

EFAULT

Systems with OSes that do not support EHCI cannot

use the EHCI handoff functionality.

Summary of Contents for IMBA-8654



















































































































































































































































Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands

IEI Technology IMBA-8654, User Manual

Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands