IEI Technology IMBA-8654 User Manual Download

Page: 106 / 242

IMBA-8654 Motherboard

Page 88

Step 1:

Place the cooling kit onto the LGA775 CPU. Make sure the CPU cable can be

properly routed when the cooling kit is installed.

Step 2:

Properly align the cooling kit. Make sure the four spring screw fasteners can

pass through the pre-drilled holes on the PCB.

Step 3:

Mount the cooling kit. Gently place the cooling kit on top of the CPU. Make sure

the four threaded screws on the corners of the cooling kit properly pass through

the predrilled holes on the bottom of the PCB.

Step 4:

Secure the cooling kit. From the solder side of the PCB, align the support

bracket to the screw threads on heat sink that were inserted through the PCB

holes. (See

Figure 5-6

)

Figure 5-6: Securing the Heat sink to the PCB Board

Step 5:

Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each

nut a few turns at a time and do not over-tighten the screws.

Step 6:

Connect the fan cable. Connect the cooling kit fan cable to the fan connector on

the IMBA-8654. Carefully route the cable and avoid heat generating chips and

fan blades.

Step 0:

Summary of Contents for IMBA-8654



















































































































































































































































Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands

IEI Technology IMBA-8654, User Manual

Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands