IEI Technology IMBA-8654 User Manual Download

Page: 172 / 242

IMBA-8654 Motherboard

Page 154

Enabled D

EFAULT

If there is an error during boot up, the system waits for a

user to press “F1” and enter the BIOS to rectify the

problem. The BIOS can then be adjusted to the correct

settings.

Hit ‘DEL’ Message Display [Enabled]

Use the

Hit “DEL” Message Display

option to specify whether the instruction to hit the

delete button to enter BIOS during POST appears or not.

Disabled

No message displayed during POST

Enabled D

EFAULT

Displays

“

Press DEL to run Setup

” message in

POST

Interrupt 19 Capture [Disabled]

Use the

Interrupt 19 Capture

option to allow optional ROMs such as network controllers

to trap BIOS interrupt 19.

Disabled D

EFAULT

Does not allow optional ROM to trap interrupt 19

Enabled

Allows optional ROM to trap interrupt 19

6.5.2 Boot Device Priority

Use the Boot Device Priority menu (

BIOS Menu 16

) to specify the boot sequence from the

available devices. Possible boot devices may include:

FLOPPY DRIVE

HDD

CD/DVD

Summary of Contents for IMBA-8654



















































































































































































































































Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands

IEI Technology IMBA-8654, User Manual

Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands