IEI Technology IMBA-8654 User Manual Download

Page: 138 / 242

IMBA-8654 Motherboard

Page 120

Primary IDE (Slave)

Secindary IDE (Master)

Secondary IDE (Slave)

Third IDE (Master)

Fourth IDE (Master)

The IDE Configuration menu (

BIOS Menu 4

) allows changes to the configurations for the

IDE devices installed in the system. If an IDE device is detected, and one of the above

listed four BIOS configuration options are selected, the IDE configuration options shown in

Section 6.3.2.1

appear.

6.3.2.1 IDE Master, IDE Slave

Use the IDE Master and IDE Slave configuration menu (

BIOS Menu 5

) to view both

primary and secondary IDE device details and configure the IDE devices connected to the

system.

BIOS Menu 5: IDE Master and IDE Slave Configuration

Auto-Detected Drive Parameters

The “grayed-out” items in the left frame are IDE disk drive parameters automatically

detected from the firmware of the selected IDE disk drive. The drive parameters are listed

as follows:

Summary of Contents for IMBA-8654



















































































































































































































































Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands

IEI Technology IMBA-8654, User Manual

Search results

Summary of Contents for IMBA-8654

Reviews:

Related manuals for IMBA-8654

Brands by name

Popular brands