IEI Technology IMB-C2160 User Manual Download

Page: 22 / 205

IMB-C2160 Mic ro -ATX Mo th e rb o a rd

P a g e 7

1.7

Te c h n ic a l S p e c ific a tio n s

IMB-C2160 technical specifications are listed below.

Specification/Model IMB-C2160

Form Factor

Micro-ATX

CPU

LGA1155 socket supports Intel® Xeon® E3 and Intel® Core™ i3

quad/dual core processors

System Chipset

Intel® C216

Graphics Engine

Supports DX10.1 and OpenGL 3.0

Full MPEG2, VC1, AVC Decode

Display Output

VGA integrated in the Intel® C216

Memory

Four 240-pin 1600/1333MHz dual-channel DDR3 SDRAM ECC and

non-ECC unbuffered DIMMs supported (system max. 32GB)

Audio

Realtek ALC662 HD audio codec (Line-in, Line-out, Mic)

BIOS

UEFI BIOS

Digital I/O

24-bit Digital I/O (24-bit GPIO is for programming I/O)

Ethernet

Intel® 82579 PHY with Intel® AMT 8.0 supported

Intel® 82574L PCIe controller

Super I/O

Fintek F81866

Watchdog Timer

Software programmable supports 1~255 sec. system reset

Expansions

PCIe

One PCIe x16 slot

One PCIe x16 slot (with x8 signal)

Two PCIe x4 slots

I/O Interface Connectors

Audio Connectors

Three external audio jacks (Line-in, Line-out, Mic)

Ethernet

Two RJ-45 ports

Keyboard/Mouse

One external PS/2 keyboard/mouse port

One internal 6-pin keyboard/mouse connector

Summary of Contents for IMB-C2160














































































































































































































Search results

Summary of Contents for IMB-C2160

Reviews:

Related manuals for IMB-C2160

Brands by name

Popular brands

IEI Technology IMB-C2160, User Manual

Search results

Summary of Contents for IMB-C2160

Reviews:

Related manuals for IMB-C2160

Brands by name

Popular brands