manualshive.com logo in svg

IDT TSI384, User Manual

The IDT TSI384 user manual provides detailed instructions and information on operating this exceptional product. You can conveniently download the manual for free from our website, enabling you to make the most out of your TSI384 experience. Discover the full potential and capabilities of this innovative device with our comprehensive manual.

Share
Download
background image

273

Tsi384 User Manual

May 5, 2014

Integrated Device Technology
www.idt.com

Glossary

ADB

Allowable disconnect boundary. An ADB is a naturally aligned 128-byte boundary. PCI-X bus 
masters and targets are permitted to disconnect burst transactions only on ADBs. 

Address decode window

The address range defined by a device’s base address registers when operating in non-transparent 
addressing mode. If a transaction address on the bus falls within a device’s address decode window, 
the device claims the transaction. 

ADQ

ADB deliminated quanta. An ADQ is a portion, or all of, a 128-byte buffer that fits between two 
allowable disconnect boundaries (ADBs). The ADQ forces address alignment of the data packets 
within a device’s internal buffers. For example, a 128-byte data transfer that crosses an ADB (that is, 
not aligned) uses two ADQs for the transfer. 

Attribute

It is the 36-bit field contained on CBE[3:0]_ and AD[31:0] during the attribute phase of a PCI-X 
transaction. The initiator of a transaction is responsible for driving the attribute. 

Attribute phase

This phase occurs after the address phase(s), and defines additional information about the current 
PCI-X transaction. The lower bus halves (C/BE[3:0]_ and AD[31:0]) contain the attributes. The upper 
bus halves (C/BE[7:4]_ and AD[63:32]) are reserved and driven high by 64-bit initiators. 

Base and limit register

A configuration register that stores memory or I/O address decode information in a device. If the 
address of a transaction falls within the window defined by a device’s base and limit registers, the 
device claims the transaction. Base and Limit registers are used only by transparent bridges. 

CompactPCI

cPCI. It is an adaptation of the 

PCI Local Bus Specification (Revision 2.2)

 for Industrial and/or 

embedded applications that require a more robust mechanical form factor than desktop PCI. 

Completer (PCI-X)

The device that is addressed by a PCI-X transaction (other than a split transaction). 

Completer (PCIe)

The device that is targeted by a requester during a PCIe transaction. A requester reads data from a 
completer, or writes data to a completer. A requester can be either a root complex or an endpoint 
device. 

Completer ID

This value uniquely identifies the completer of a transaction request. It consists of a completer’s bus 
number, device number, and function number. 

Configuration transaction

A read or write access of a PCI device’s configuration registers. 

Downstream port

A PCIe port that points in the direction away from the root complex (for example, a root complex port). 

Egress port

A PCIe port that transmits a packet to another PCIe device. 

Endpoint

A type of PCIe device, or mode of operation, that function as requesters or completers of PCIe 
transactions (examples include Ethernet, USB, and graphic devices). If a PCIe port is not configured 
as a root complex or a switch then it is considered an endpoint. An endpoint can support up to eight 
functions. 

Fairness algorithm

Arbitration logic that helps low and high priority devices gain fair access to a peripheral bus. This logic 
also helps prevent deadlocks among bus-mastering devices in a system. 

Summary of Contents for TSI384


























































































































































































































































































Reviews:

No comments

Related manuals for TSI384

Ratoc Systems SmartMedia Adapter PC Card REX-SMA01F Product Manual preview
SmartMedia Adapter PC Card REX-SMA01F
Brand: Ratoc Systems Pages: 75
ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Brand: ebm-papst Pages: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Brand: ebm-papst Pages: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Brand: ebm-papst Pages: 5
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Brand: ebm-papst Pages: 16
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Brand: Cromemco Pages: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Brand: Verizon Wireless Pages: 39
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
Lantronix N-FXE 02B Series User Manual preview
N-FXE 02B Series
Brand: Lantronix Pages: 10
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
Zonet ZEN3320E Quick Installation Manual preview
ZEN3320E
Brand: Zonet Pages: 1
IEI Technology PUZZLE-IN005 User Manual preview
PUZZLE-IN005
Brand: IEI Technology Pages: 106

Brands by name

Popular brands

Load more brands