IDT TSI384 User Manual Download Page 140 | Manualshive

Page: 140 / 281

background image

13. JTAG

140

Tsi384 User Manual
May 5, 2014

Integrated Device Technology

www.idt.com

•

DR[18:0] = 19b’0

Note

: Bit 0 is shifted first, and bit 68 is shifted last.

3.

Move to the “Run-test idle” state and loop in this state for a minimum of 20 TCK cycles.

4.

Move to the “Shift-DR” state again and shift the Ready bit and Error bit through JTAG_TDO (see

).

•

First bit shifted out is the Ready bit.

•

Second bit shifted out is the Error bit.

•

Verify that the Ready bit is at logic high and the Error bit is at logic low.

Note

: To prevent corruption, the DR register must be loaded as described in step 2 while

shifting out through JTAG_TDO for observation.

5.

Go back to step 2 to perform another write.

13.6.3

Read Access to Registers from JTAG Interface

Complete the following steps to read a device register through the JTAG Interface:

1.

Move to the TAP controller “Shift-IR” state and program the instruction register with IRAC
instruction by writing into Instruction Register bits with 0x3F_FFFF_FFFF_FFFD.

This step is optional if the instruction register is already programmed during the write cycle.

2.

Move to the “Shift-DR” state and shift the R/W = 0 and the address[9:0] serially in the TDI pin. To
prevent corruption of unused bits, the full DR bits have to be written as follows (see also

):

•

DR[68:64] = 5b’0

•

DR[63:54] = ADDR[9:0]

1

•

DR[53] = R/W

•

DR[52:21] = DATA[31:0]

•

DR[20:19] = 2b’0

•

DR[18:0] = 19b’0

Note

: Bit 0 is shifted first, and bit 68 is shifted last.

3.

Move to the “Run-test idle” state and loop in this state for a minimum of 20 TCK cycles.

4.

Move to the “Shift-DR” state again and shift the Ready bit, Error bit, and data[31:0] out through
JTAG_TDO (see

).

•

First bit shifted out is the Ready bit.

•

Second bit shifted out is the Error bit.

1. Note that the address here is the DWORD address, not the byte address. Take the byte address and remove the 2 LSBs, >>2.

«
...
138
139
140
141
142
...
»

Summary of Contents for TSI384


























































































































































































































































































Reviews:

No comments

Related manuals for TSI384

Brand: Barco Pages: 100

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

Brand: Clavister Pages: 89

Brand: ZALMAN Pages: 22

Brand: NA Pages: 22

Brand: Campbell Pages: 38

Brand: TANDBERG Pages: 3

UM10301 PCA8565

Brand: NXP Semiconductors Pages: 54

Brand: Rajant Corporation Pages: 40

Brand: Dataprobe Pages: 16

ELITE LCD UPGRADE KIT

Brand: Corsair Pages: 11

Brand: TECO Pages: 24

Brand: Jabra Pages: 2

Brand: Vivotek Pages: 185

Brand: Transition Networks Pages: 5

X-NUCLEO-GFX01M Series

Brand: ST Pages: 31

BNI EIP-508 05-Z015 Series

Brand: Balluff Pages: 74

Brand: RadioLAN Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands