IDK MSD-72 Series Command Reference Manual Download

Page: 49 / 113

MSD-72 series Command Guide

@GSM / @SSM

Automatic measurement when unregistered signal is input

Getting

Command

@GSM

Response

@GSM, mode

Setting

Command

@SSM, mode

Response

@SSM, mode

Parameter

mode: Automatic measurement

0 = Not execute, 1 = Execute [Default]

Getting

example

Command

Response

@GSM

@GSM,1

Description Getting the set automatic measurement mode when unregistered signal is input.

Setting

example

Command

Response

@SSM,1

Description Setting the automatic measurement to be executed when unregistered signal is

input.

Remarks

－

@RTT

Loading device data

Setting

Command

@RTT, ch (, table)

Response

@RTT, ch (, table)

Parameter

ch: Input channel

1 = IN1 to 9 = IN9

table: Device table

1 to 99 (Registered device data),

100 to 100+n (Preset device

data. ”n” varies depending on input signal, but

0 for most cases.)

Only for analog input, specify the device table.

Setting

example

Command

Response

@RTT,1

Description Reconfiguring IN1 input timing setting to the value detected automatically.

Setting

example

Command

Response

@RTT,6,2

Description Setting IN6 input timings to the values saved in the device table 2.

Remarks

This command is valid only if signal is input.

For analog input, this command is valid only if the device data of input signal is

registered.

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands