IDK MSD-72 Series Command Reference Manual Download

Page: 8 / 113

MSD-72 series Command Guide

2.1.3 Setting up RS-232C communication

(1) Connect the MSD and the control device via an RS-232C cable.

(2) Set the RS-232C communication as follows:

・

RS-232C communication: baud rate, data bit length, parity check, and stop bit

・

Operation mode of RS-232C communication:

“RECEIVER”

【

Reference: User

’s Guide

】

(3) For the control device, set the same values in the same way as RS-232C communication (baud rate, data

bit length, parity check, and stop bit) in step (2) above.

(4) Send a communication command from the control device to the MSD in order to check the control status of

the MSD.

Step (2)

Step (1)

RS-232C cable

Step (4)

Communication

command

Step (3)

Laptop

(Controller)

[Figure 2.3] Setting RS-232C communication

Operation example of RS-232C communication

Laptop

Projector

RS-232C cable

Power amplifier

Controlling the MSD using

Communication commands

Controlling the MSD using

Communication commands

Outputting control commands

to external device

[Figure 2.4] RS-232C communication

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands