IDK MSD-72 Series Command Reference Manual Download

Page: 73 / 113

MSD-72 series Command Guide

@GSP / @SSP

The number of speakers (cont

’d)

Getting

example

Command

Response

@GSP,1

@GSP,1,6,0,1,2,3

Description

Getting the IN1 speaker configuration.

Six speakers (Front Left / Right, Low Frequency Effect, Front Center, Rear Left /

Right) are used.

Setting

example

Command

Response

@SSP,2,8

Description

Setting IN2 speaker configuration to Front Left / Right, Low Frequency Effect,

Front Center, Rear Left / Right, Rear Left / Right Center (eight speakers).

Completed normally.

Setting

example

Command

Response

@SSP,3,8,0,3,5,6,7

@ERR,1

Description

Setting IN3 speaker configuration to Front Left / Right, Rear Left / Right, Front

Left / Right Center, Rear Left / Right Center, Front Left / Right Wide.

The number of speakers is 10 which exceeds the settable value, and it causes

the error.

Remarks

These commands are only for digital input.

IN8 and IN9 are available only when

“1” (Digital signal). is selected for “

@GIN /

@SIN

”.

“0” (Analog signal) is selected, “-1” is returned.

@RME

Copying EDID

Setting

Command

@RME, out, number, name

Response

@RME, out, number, name

Parameter

out: Connector to be loaded

1 = OUT1 to 4 = OUT4

number: Destination COPY DATA number

1 to 8

name: COPY DATA name

Up to 10 characters using 20 to 7D from ASCII codes.

You can skip this setting. In this case, only EDID settings are saved without

changing currently saved name.

Setting

example

Command

Response

@RME,1,1

Description Loading EDID data of the sink device connected to OUT1 and saving it in COPY

DATA 1.

Setting

example

Command

Response

@RME,3,4,800x600

Description Loading EDID data of the sink device connected to OUT3, naming it

“800x600”

and saving it in COPY DATA 4.

Remarks

@GED / @SED EDID

Summary of Contents for MSD-72 Series


















































































































Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands

IDK MSD-72 Series, Command Reference Manual

Search results

Summary of Contents for MSD-72 Series

Reviews:

Related manuals for MSD-72 Series

Brands by name

Popular brands