IDK MSD-72 Series Command Reference Manual Download | Manualshive

Page: 12 / 113

background image

MSD-72 series Command Guide

12

2.2.4 The number of TCP-IP connections

The MSD series can connect up to eight connections (eight ports) simultaneously. If the MSD is controlled
from nine or more PCs, they may not be connected to the MSD normally, since the number of connections
that can be used is limited.

If you use nine connections or more, execute TCP-IP connection/close every time the communication
command is sent or received from the software of user

’s side. By doing so, MSD’s ports are occupied or

released so that nine or more connections can be connected logically.

[Table 2.4] Increasing connections

Your PC software

MSD

TCP-IP connection

→

(Occupied by 1 port)

Send command (@xxx)

→

←

Send back command
(@xxx)

TCP-IP close

→

(Release 1 port)

Note:

If any command is not sent from the PC side to the MSD for 30 seconds, the MSD disconnects the

connection to avoid the limitation problem on the number of connections. As a result, connection needs to be

established again from the PC side after the current connection of the PC is disconnected.

(Since the number of ports in the MDS is eight, ports are occupied permanently if the PC is turned off while

connections are valid. To prevent this, the MSD disconnects connections if no communication command is

sent from the PC side.)

«
...
10
11
12
13
14
...
»

Summary of Contents for MSD-72 Series


















































































































Reviews:

No comments

Related manuals for MSD-72 Series

Brand: Magnetrol Pages: 12

Brand: Magnimage Pages: 53

ATLONA Omega AT-OME-MS52W

Brand: Panduit Pages: 123

Atlona AT-OME-MS42

Brand: Panduit Pages: 86

IP-Reach IPR-M1

Brand: Raritan Pages: 4

S5800-EI Series

Brand: H3C Pages: 61

Brand: Eaton Pages: 2

Brand: GeoVision Pages: 7

Brand: CYP Pages: 28

MultiView CE-H26311-S1

Brand: SIIG Pages: 24

Brand: Guntermann & Drunck Pages: 8

Brand: SMART-AVI Pages: 2

Brand: NeoPro Pages: 36

Brand: H3C Pages: 3

Brand: PTN Pages: 44

SM24-1000SFP-AH

Brand: Transition Networks Pages: 76

Brand: Atlona Pages: 13

IMI SENSORS EX686B77

Brand: PCB Piezotronics Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands