Idemia MorphoAccess VP MD Installation Manual Download

Page: 65 / 75

MorphoAccess® VP MD

– Installation Guide

Annex 1 : Finger Placement Recommendations

2019_200000XXXX-V0

IDEMIA

OCUMENT

EPRODUCTION AND

ISCLOSURE

ROHIBITED

December 2018

Most useful areas for biometric data

Areas with the most useful biometric data are different according to the type of
biometric data:



Fingerprint: the most useful zone is around the centre of the first phalanx of the

finger.



Vein network: the useful zone is between the first and third phalanx of the finger.

Figure 27: Most useful areas for biometric data

The sensor is designed so that when the fingertip is in contact with the rounded hollow
guide:



the central zone of the first phalanx is aligned with that of the section dedicated to

the fingerprint capture,



the second phalanx is positioned inside the section dedicated to capturing the finger

vein network.

Area containing the maximum
information

First
phalanx

Second
phalanx

Summary of Contents for MorphoAccess VP MD










































































Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands

Idemia MorphoAccess VP MD, Installation Manual

Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands