Idemia MorphoAccess VP MD Installation Manual Download

Page: 64 / 75

MorphoAccess® VP MD

– Installation Guide

Annex 1 : Finger Placement Recommendations

2019_200000XXXX-V0

IDEMIA

OCUMENT

EPRODUCTION AND

ISCLOSURE

ROHIBITED

December 2018

Main principles

Acquisition needs to be done with extreme care, in order to:



get the best image quality



increase recognition performance



reduce recognition time

Then, it is highly recommended to:



Maximize the contact between the fingerprint and the sensor



Exert firm, but not excessive, finger pressure on the surface of the sensor



Do not press too hard



Do not slide nor roll the finger across the sensor



Do not move the finger during acquisition



Wait for the extinction of sensor backlight before removing the finger

Summary of Contents for MorphoAccess VP MD










































































Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands

Idemia MorphoAccess VP MD, Installation Manual

Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands