Idemia MorphoAccess VP MD Installation Manual Download | Manualshive

Page: 62 / 75

background image

MorphoAccess® VP MD

– Installation Guide

Annex 1 : Finger Placement Recommendations

2019_200000XXXX-V0

IDEMIA

D

OCUMENT

-

R

EPRODUCTION AND

D

ISCLOSURE

P

ROHIBITED

62

December 2018

temperatures), deviation may be more important (worst case: - 14 seconds per 48
hours).

If the terminal is used in an application requiring high time precision, we recommend
synchronizing regularly your terminal time with an external clock (using NTP). Every 24
hours is usually enough for most applications.

Please note that the date/time of the terminal is protected from power failure during
at least 24 hours. If the duration of the power failure or power down is longer, the
date/time of the terminal will be lost.

Cleaning precautions

The use of a dry cloth is recommended to clean the terminal, especially the biometric
sensor. Acid liquids, alcohol or abrasive materials are prohibited.

«
...
60
61
62
63
64
...
»

Summary of Contents for MorphoAccess VP MD












































































Reviews:

No comments

Related manuals for MorphoAccess VP MD

Brand: Sole Diesel Pages: 8

Brand: YASKAWA Pages: 256

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: TCS Basys Controls Pages: 2

Ascotel Office 45

Brand: Aastra Pages: 40

Brand: Aastra Pages: 244

Brand: Aastra Pages: 30

Brand: Aastra Pages: 24

IntelliGate A150

Brand: Aastra Pages: 524

Ascotel IntelliGate 150

Brand: Aastra Pages: 228

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: FATEK Pages: 10

Brand: Samson Pages: 6

Brand: Water Specialist Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands