Idemia MorphoAccess VP MD Installation Manual Download

Page: 30 / 75

MorphoAccess® VP MD

– Installation Guide

Section 3 :Installation Procedure

2019_200000XXXX-V0

IDEMIA

OCUMENT

EPRODUCTION AND

ISCLOSURE

ROHIBITED

December 2018

Installation

Required tools (not supplied)



Two (2) ra two (2) ø 3.5mm max and length 30mm screws.



One (1) screwdriver adapted to screws above.



One (1) Drill (with a drill bit diameter adapted to rawplugs above).



One (1) hole saw ø 67mm.



One (1) Flat tip screwdriver (2,5mm) for block connector screws.



A (1) Torx T10 screwdriver or a (1) regular 4 mm screwdriver.



A (1) Torx T8 screwdriver.



Deadbolt/door strike



Snubber diode required to protect regulated DC power supply from inductive
kickback (1N4007 diode or equivalent recommended)



Separate power supply for the deadbolt/door strike based on supplier's
recommendations.



External relay (if required)



Networking cable

Equipment from the initial package to use



One (1) Terminal’s body.



One (1) wall plate.



Four (4) M3x25 screws.



One (1) bottom cover.



Four (4) K2.5x8 screws.



Two (2) Block connectors.



One (1) top cover.

Summary of Contents for MorphoAccess VP MD










































































Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands

Idemia MorphoAccess VP MD, Installation Manual

Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands