Idemia MorphoAccess VP MD Installation Manual Download

Page: 67 / 75

MorphoAccess® VP MD

– Installation Guide

Annex 1 : Finger Placement Recommendations

2019_200000XXXX-V0

IDEMIA

OCUMENT

EPRODUCTION AND

ISCLOSURE

ROHIBITED

December 2018

Bad finger position

The following figures show incorrect finger positions.



Do not place the fingertip on the top of the
fingertip guide.



Do not place the fingertip on the surface of the
sensor: it must be in contact with the rounded
hollow guide.



Do not leave the finger in the air.



Do not bend the finger.



Do not tilt the finger: it must be parallel with
the sensor’s walls.



Do not roll the finger.



Do not bend the finger upwards.



Do not bend the finger downwards.

Figure 29: Incorrect finger positions

Summary of Contents for MorphoAccess VP MD










































































Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands

Idemia MorphoAccess VP MD, Installation Manual

Search results

Summary of Contents for MorphoAccess VP MD

Reviews:

Related manuals for MorphoAccess VP MD

Brands by name

Popular brands