Ideal Boilers responce 100 Installation And Servicing Manual Download

Page: 48 / 64

Response 80 / 100 / 120

- Installation

SER

VICING

CH EXPANSION VESSEL REPLACEMENT

SERVICING

If the CH expansion vessel is faulty, there are 3 options:

A. If it has a punctured diaphragm, but is

otherwise leak free, then it can be left in place

and a new vessel added to the system, external to the boiler, provided it is of adequate
capacity and pre-charge pressure.

B. If there is at least 600mm clearance above the boiler, the expansion vessel can be

changed without removing the boiler (RH exit flues will have to be disturbed). Access to
the water connection of the expansion vessel is

either by removal of the right hand side

boiler panel (if there is 200mm RHS clearance)

or by removal of the fan and gas valve.

C. If there is insufficient headroom, the boiler will need to be removed. In this case,

access to the water connection of the expansion vessel will be possible by removing
the RH boiler side panel.

View of underside of boiler

Front of boiler

res 6101

For option B, proceed as follows:

B1.Isolate the electric, gas, and water services.

B2.Drain down the boiler CH circuits, using the appropriate

drain cocks.

B3.Where RH clearance is available. Unscrew the 10 screws

securing the RHS panel and remove the panel to gain
access to the expansion vessel connector.

Where RH clearance is NOT available. Remove the fan
(refer Frame 49) and gas valve (refer Frame 62) to gain
access to the expansion vessel connector.

B4.Disconnect the flue, if RH exit, and remove to the right

(general details are reverse of Frames 18 & 28).

B5.Undo the 3 screws securing the boiler panel above the

expansion vessel, and remove the panel.

C3.Undo all service unions at the base of the boiler, and

unplug and disconnect the electrical supply lead, which is
secured by one screw in the centre of the boiler base.

C4.Disconnect the flue turret and place to one side (reverse of

the assembly described in Frames 18 & 28).

C5.Lift the boiler off the wall and place horizontally, at a

convenient working height.

C6.Follow instructions B3 to B6.

C7.Return the boiler to the wall mounting frame, remaking all

connections, including the flue.

C8.Fill, pressurise and test.

C9.Remove the filling loop.

B6.Undo the water connection at the bottom of the expansion vessel.

Lift out the vessel and fit the replacement, reassembling in reverse
order - using new gaskets and 'O' rings where appropriate.

B7.Fill, pressurise and test.

B8.Remove the filling loop.

For option C, proceed as follows:

C1.Isolate the electrical, gas and water services.

C2.Drain down the boiler CH/HW circuits using the appropriate boiler

drain cocks (refer Frame 68).

Summary of Contents for responce 100

































































Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands

Ideal Boilers responce 100, Installation And Servicing Manual

Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands