Ideal Boilers responce 100 Installation And Servicing Manual Download Page 42

Page: 42 / 64

Response 80 / 100 / 120

- Installation

PRINTED CIRCUIT BOARD REPLACEMENT

HW EXPANSION VESSEL

SER

VICING

SERVICING

The Response uses:

PCB 41 - Ignition sequence

PCB 40 - Logic sequence

Fan speed control

1. Isolate the electrical supply.

Refer to Frame 54.

2. Remove the front panel.

3. Remove the PCB cover

4. Disconnect all 'Molex' plugs

feeding the PCB to be
changed.

5. Release the clips and

remove the PCB.

6. Fit the new board onto the

clips.

7. Replace all 'Molex'

connectors. Note that the
connectors are made non-
interchangeable. If in doubt,
refer to Frame 40 - Pictorial
Wiring.

8. Reassemble in reverse

order

9. Test both DHW and CH

modes of operation.

1. Disconnect the electrical

supply to the boiler.

2. Remove the front and sealing

panels. Refer to Frame 48.

3. Close the isolating valve on

the HW supply then release
pressure by opening a hot tap.
Note.

Ensure valve markings

are as shown.

4. Drain, using the drain point on

the isolating valve.

5. Unscrew the HW expansion

vessel, which may be finger-
tight. If necessary, remove the
fan (see Frame 65). To access
use a spanner on the hexagon
nut behind the vessel.

6. Replace with new sealing

gasket and vessel.
Reassemble in reverse order
and test fire.

PCB 41

Summary of Contents for responce 100

































































Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands

Ideal Boilers responce 100, Installation And Servicing Manual

Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands