Ideal Boilers responce 100 Installation And Servicing Manual Download Page 47

Page: 47 / 64

Response 80 / 100 / 120

- Installation

SERVICING

SER

VICING

PRESSURE RELIEF VALVE (Safety Valve) REPLACEMENT

1. Isolate the electrical supply. Refer to

Frame 54.

2. Remove the pump. Refer to Frame 69.

3. Disconnect the mains electrical

connection from the bottom panel.
Disengage the 2 halves of the
connector.

4. Remove the boiler bottom panel.

5. Close the cocks on the CH flow and

return pipework below the boiler. Drain
down. Refer to Frame 68.

6. Disconnect the discharge pipe to the

pressure relief valve.

7. Undo the connection securing the valve

to the boiler.

8. Replace with a new valve and restore

the pipework, in reverse order, using
new sealing washer.

9. Open cocks, fit filling loop, fill, vent and

pressurise to 1 bar (or as required).

10. Restore the electrical supply and set the

heating controls, to test-fire the boiler.

11. Vent air and top up the pressure again,

as required.

12. Remove the filling loop.

MAINS TRANSFORMER REPLACEMENT

1. Isolate the electrical supply to the boiler.

Refer to Frame 54.

2. Remove the boiler front panel. Refer to

Frame 48.

3. Release the screws securing the PCB

cover and remove the cover.

4. Disconnect the transformer electrical

leads at the in-line connector

5. Release the transformer mounting

screws.

6. Fit the replacement transformer and

complete the reassembly in reverse
order.

Summary of Contents for responce 100

































































Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands

Ideal Boilers responce 100, Installation And Servicing Manual

Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands