Ideal Boilers responce 100 Installation And Servicing Manual Download

Page: 52 / 64

Response 80 / 100 / 120

- Installation

FAULT FINDING

AUL

T FINDING

Has overheat
'stat tripped ?

(reset button

under RHS of

boiler)

Fan not running

Foot Note:

Presence of live supply on a terminal may be checked with a multimeter set to the appropriate AC range (apply the other probe

of the meter to mains neutral, e.g. on terminal N of the programmer terminal strip).

Can it be reset when the boiler is cold

Reset 'stat. Check

temperatures as the

boiler warms up. If the

overheat 'stat trips:

below 90° - replace the

overheat stat.

above 90° - check CH/

HW thermistors and
replace as required.

YES

Replace

overheat

'stat

Check lead to

transformer

Replace transformer

Is there 24-28 V AC between secondary

terminals (red and black leads) of transformer

YES

Has secondary fuse F1 on PCB 40 blown ?

Examine fan wiring harness, checking

especially for loose connections or

disconnected wires.

If no fault found, check fan by substitution.

Does replacement fan run OK ?

Leave replacement PCB fitted

but check the fuses on it.

Fit replacement fan.

Refit original fan. Check

PCB 40 by substitution.

Does fan now run ?

YES

Replace fuse. Examine fan harness, checking

especially for short circuits between wires or

terminals.

If no fault found, power up board

without fan

harness connected. Does fuse F1 blow ?

YES

EXIT

YES

Does the fan

run ?

Replace

PCB 40

Is there mains voltage

between primary

terminals (brown and

blue leads) of mains

transformer ? (Expect

230V 50Hz ± 10%)

YES

Has the

mains fuse F2 on PCB 40 blown ?

Is there a supply at PCB 40 at its mains input

connector? (Expect 230V 50 Hz ± 10%)

YES

Reconnect the

harness and fan and

restore power.

Does the fuse blow ?

Check continuity

of the water

pressure switch

and overheat

'stat - replace as

required.

Make sure the boiler mains switch is ON

and the heating switch is on, if required.

Is the 'Mains On' neon lit ?

YES

Check connections and

continuity of EMC filter

YES

Rectify

external fault

Is there mains voltage to the boiler ?

Go to Frame 86

Check pump for shorts

between L/N and L/E.

If no fault found

disconnect the pump

and lead to PCB 41,

renew fuse and

reconnect each item

one by one until the

faulty item is

determined

YES

Check fan by substitution

YES

WARNING. When panels are removed for service, live parts are exposed so caution should be exercised when fault-finding.

YES

Is the system pressure gauge indicating

water pressure below 0.5 bar ?

Summary of Contents for responce 100

































































Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands

Ideal Boilers responce 100, Installation And Servicing Manual

Search results

Summary of Contents for responce 100

Reviews:

Related manuals for responce 100

Brands by name

Popular brands