Ideal Boilers responce 100 Installation And Servicing Manual Download Page 19 | Manualshive

Page: 19 / 64

background image

19

Response 80 / 100 / 120

- Installation

19

TERMINAL WALL PLATE

This plate allows neat concealment and full
compression of the rubber seal. It should be used,
where practicable::

a. When the wall is more than 24" thick (to support the

flue weight and prevent movement).

or

b. When the hole has not broken through neatly.

or

c. When the wall face is rough and the rubber seal on

its own would be ineffective.

1. Position the terminal wall plate over the terminal.

2. Drill 4 fixing holes with a 7mm (

1/4

") masonry drill.

3. Insert the 4 plastic plugs provided in flue pack B.

4. Secure the plate with 4 of the No.10 x 2" screws provided

in flue pack B.

Note.

If the terminal is less than 2m (6' 6") above ground

level, an approved terminal guard should be fitted.
Refer to 'Flue Installation', Page 7.

INSTALLATION

REAR FLUE OUTLET

«
...
17
18
19
20
21
...
»

Summary of Contents for responce 100

































































Reviews:

No comments

Related manuals for responce 100

Brand: Glow-worm Pages: 28

Brand: Saturn Pages: 17

Brand: RBI Pages: 20

Brand: Reznor Pages: 48

Brand: Ravelli Pages: 200

Brand: PeerlessBoilers Pages: 70

Brand: Lochinvar Pages: 16

Brand: Lochinvar Pages: 44

Brand: Lochinvar Pages: 40

Brand: Fröling Pages: 76

Lambdatronic SP 3200

Brand: Fröling Pages: 129

ATLAS D 30 SI UNIT

Brand: Ferroli Pages: 88

ATLAS 25 SI UNIT

Brand: Ferroli Pages: 100

ATLAS D ECO 56 UNIT

Brand: Ferroli Pages: 88

Brand: Ferroli Pages: 96

Brand: Truma Pages: 6

Brand: Potterton Pages: 20

Knockdown RV-500

Brand: Bryan Boilers Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands