Ideal Boilers responce 100 Installation And Servicing Manual Download Page 6 | Manualshive

Page: 6 / 64

background image

6

Response 80 / 100 / 120

- Installation

2

BOILER DIMENSIONS, SERVICES & CLEARANCES

all dimensions in mm (in.)

17.

The following minimum clearances must be
maintained for operation and servicing.
Additional space will be required for installation,
depending upon site conditions.

Side and Rear Flue

a. Provided that the flue hole is cut accurately,

e.g. with a core drill, the flue can be installed
from inside the building where wall
thicknesses do not exceed 600mm (24").
Where the space into which the boiler is
going to be installed is less than the length
of flue required the flue must be fitted from
the outside.

Installation from inside ONLY

b. If a core boring tool is to be used inside the

building the space in which the boiler is to
be installed must be at least wide enough to
accommodate the tool.

Boiler connections are made on the mounting frame. Refer to Frame

GENERAL

Front clearance

The minimum front clearance when built in to a
cupboard is 5mm (

1/4

") from the cupboard door

but 450mm (17

3/4

") overall clearance is still

required, with the cupboard door open, to allow
for servicing. See Table 4.

Distance X is 20mm for DHW pipes and safety valve outlet.

Distance X is 23.5mm for CH pipes and gas inlet.

Per side

5 mm

Top

160 mm

(depth of elbow and lift

Front

450 mm

clear of spigot space,

Bottom

150 mm

internal wall ring plate)

CLEARANCES

*

Bottom clearance

Bottom clearance after installation can be
reduced to 10mm in an adequately ventilated
enclosed cupboard. However, 150 mm must
be available for servicing.

Dimension y

Boiler only

with stand-

off brackets

139mm

169mm

(5 (

7/16

")

(6

5/8

")

«
...
4
5
6
7
8
...
»

Summary of Contents for responce 100

































































Reviews:

No comments

Related manuals for responce 100

Brand: MONTAGUE Pages: 15

Brand: Lamborghini Caloreclima Pages: 40

Brand: CHAFFOTEAUX Pages: 16

Brand: STIEBEL ELTRON Pages: 60

Brand: Vollrath Pages: 6

Logano plus SB315

Brand: Buderus Pages: 16

Brand: Sime Pages: 48

Brand: Sime Pages: 16

Format System 25 HE

Brand: Sime Pages: 32

FORMAT DGT HE 12

Brand: Sime Pages: 32

Brand: Atag Pages: 10

Brand: Atag Pages: 64

Brand: Atag Pages: 64

Brand: Navien Pages: 24

Brand: Sime Pages: 104

Brand: Sime Pages: 104

Brand: Bumham Pages: 48

Brand: Powermatic Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands