ICT ICT240DB-8IRC Instruction Manual Download Page 3

Page: 3 / 32

Innovative Circuit Technology Ltd.

Contents

PRODUCT DESCRIPTION ....................................................................... 4

INSTALLATION ..................................................................................... 5

OPERATION ......................................................................................... 9

Status Indicators and Alarms

......................................................

TCP/IP WEB BASED INTERFACE ........................................................... 10

Status and Control

......................................................................

Device Setup

...............................................................................

Bus Setup

.....................................................................................

Output Setup

...............................................................................

Network setup

............................................................................

E-mail Setup

................................................................................

Alarm setup

.................................................................................

User Setup

...................................................................................

Maintenance

................................................................................

MOBILE WEB INTERFACE .................................................................... 24

PASSWORD RESET .............................................................................. 25

ROUTER CONFIGURATION .................................................................. 26

TEXT MESSAGE ALARM NOTIFICATIONS .............................................. 28

TROUBLESHOOTING ........................................................................... 28

PRODUCT SPECIFICATIONS ................................................................. 30

LIMITED WARRANTY .......................................................................... 32

Summary of Contents for ICT240DB-8IRC

































Search results

Summary of Contents for ICT240DB-8IRC

Reviews:

Related manuals for ICT240DB-8IRC

Brands by name

Popular brands

ICT ICT240DB-8IRC, Instruction Manual

Search results

Summary of Contents for ICT240DB-8IRC

Reviews:

Related manuals for ICT240DB-8IRC

Brands by name

Popular brands