background image

LIMITED WARRANTY 

ICT Ltd. warrants to the original consumer purchaser that this product shall be in 
good  working  order,  free  from  defects  in  materials  and  workmanship,  for  a 
period of three (3) years from the date of purchase. Should failure occur during 
the  above  stated  time  period,  then  ICT  will,  at  its  option,  repair  or  replace  this 
product at no additional charge except as set forth below. All parts, whether for 
repair  or  replacement,  will  be  furnished  on  an  exchange  basis.  All  exchange 
pieces become the property of ICT. This limited warranty shall not apply if the ICT 
product has been damaged by unreasonable use, accident, negligence, disaster, 
service, or modification by anyone other than the ICT factory. 
 
Limited warranty service is obtained by delivering the product during the above 
stated three (3) year warranty period to an authorized ICT dealer or ICT factory 
and providing proof of purchase date. If this product is delivered by mail, you will 
insure  the  product  or  assume  risk  of  loss  or  damage  in  transit,  and  prepay 
shipping charges to the factory. 
 
Every reasonable effort has been made to ensure that ICT product manuals and 
promotional  materials  accurately  describe  ICT  product  specifications  and 
capabilities  at  the  time  of  publication.  However,  because  of  ongoing 
improvements and updating of ICT products, ICT cannot guarantee the accuracy 
of  printed  materials  after  the  date  of  publication  and  disclaims  liability  for 
changes, errors or omissions. 
 
If  this  ICT  product  is  not  in  good  working  order,  as  outlined  in  the  above 
warranty, your sole remedy shall be repair or replacement as provided above. In 
no  event  will  ICT  be  liable  for  any  damages  resulting  from  the  use  of  or  the 
inability  to  use  the  ICT  product,  even  if  an  ICT  employee  or  an  authorized  ICT 
dealer has been advised of the possibility of  such damages, or for any claim by 
any other party. 
 
ICT reserves the right to make changes without further notice to any products or 
documentation for improvement of reliability, function, or design. 
 
ICT  Ltd.  does  not  recommend  use  of  its  products  in  life  support  applications 
wherein  a  failure  or  malfunction  of  the  product  may  directly  or  indirectly 
threaten life or cause injury. The user of ICT products, which are to be used in life 
support  applications  as  described  above,  assumes  all  risks  of  such  use  and 
indemnifies ICT against all damages. 

 
 

INNOVATIVE CIRCUIT TECHNOLOGY LTD. 

26921 Gloucester Way 

Langley, British Columbia, Canada   V4W 3Y3 

604.856.6303  

F

 604.856.6365   

www.ict-power.com

 

 
 

 

Summary of Contents for ICT240DB-8IRC

































Reviews: