background image

 

 

ZT-2570/ZT-2571 

User Manual 

Warranty 

All products manufactured by ICP DAS are under warranty regarding 

defective materials for a period of one year, beginning from the date of 

delivery to the original purchaser. 

Warning 

ICP DAS assumes no liability for any damage resulting from the use of 

this product. ICP DAS reserves the right to change this manual at any 

time without notice. The information furnished by ICP DAS is believed to 

be accurate and reliable. However, no responsibility is assumed by ICP 

DAS for its use, not for any infringements of patents or other rights of 

third parties resulting from its use. 

Copyright 

Copyright © 2013 by ICP DAS. All rights are reserved. 

Trademark

 

Names are used for identification only and may be registered trademarks 

of their respective companies. 

Technology Support 

 

If you have any problems, please feel free to contact us via 
email at 

[email protected]

 

ГК

 

Атлант

 

Инжиниринг

 – 

официальный

 

представитель

 

в

 

РФ

 

и

 

СНГ

 

+7(495)109-02-08 [email protected] www.bbrc.ru 

Summary of Contents for ZT-2570


























































Reviews: