iConyx IC16/8A Owner'S Manual Download Page 49

Page: 49 / 50

Remove the 9 machine screws that secure the power supply/amplifier assembly to the frame. Three are located above

the heat sink, three are located below and three are located near the center of the heat sink. See below. note that when

the array module is mounted on the wall, you will first need to rotate it 90 degrees to gain access to the screws.

Move the assembly slightly toward the top of the module and then carefully lift the assembly out through the side of the

cabinet. Note that when the array module is mounted on the wall, you will need to lift the assembly up slightly before slid-

ing it out.

Reverse the procedure to install the replacement assembly.

Set the address dip switches of the new assemby to the same address as the assembly being replaced.

Owners Manual

Summary of Contents for IC16/8A



















































Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands

iConyx IC16/8A, Owner'S Manual

Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands