iConyx IC16/8A Owner'S Manual Download Page 9

Page: 9 / 50

ADDRESS NUMBER VERIFICATION

1. Iconyx steerable column loudspeakers are digitally controlled and each 8-channel module must have a separate and

distinct address number. The address number for each module is set using a Binary coding system and 8 on/off dip

switches. The switches are located behind each module’s rear access plate.

The switches are set at the factory based on the size and quantity of steerable column loudspeakers ordered. You may

want to check and record these settings before installing the loudspeakers. It is a lot easier to do it now than it will be after

the loudspeakers are installed.

2. Remove the access plate(s) and locate the switches. Each 8-channel module will have an access plate.

Notice that there are 8 on/off DIP switches. The switches are “ON” when set to the position closest to the num-

bers and “OFF” when set to the other position.

Owners Manual

Summary of Contents for IC16/8A



















































Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands

iConyx IC16/8A, Owner'S Manual

Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands