iConyx IC16/8A Owner'S Manual Download Page 10

Page: 10 / 50

Common practice is to number the 8-

channel modules consecutively starting

at 01 with the bottom module. In an

IC32A, for example, the bottom module

would be 01 and the ones on top of it

numbered 02, 03 and 04. If the system

had two IC32A’s, the second IC32A

would have its modules labeled 05, 06,

07 and 08 with number 05 being the bot-

tom module.

SOFTWARE INSTALLATION &

SETUP

Iconyx steerable column loudspeakers

are digitally controlled and a PC with

appropriate software is needed during

installation and setup. Once the setup is

completed the PC is no longer needed

unless the system parameters need to

be adjusted or changed.

The Iconyx software requires a PC

meeting at least the following basic

requirements:

Processor Speed:

800 MHz Pentium or higher

Memory:

256 MB or higher

Interface:

At least one available USB port compliant with USB1.1

Operating System:

Windows 2000 SP4 or Windows XP SP1 or higher

Operating System Add-Ons: .NET Framework (provided with the Iconyx software)

Screen Resolution:

1024 x 768 or higher

Browser:

Internet Explorer v5.0 or higher

Note that Windows 95 and Windows 98 are not supported.

A typical system layout is shown below.

RS422 Contol Cable

Audio Cable

From Audio Source

Owners Manual

Summary of Contents for IC16/8A



















































Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands

iConyx IC16/8A, Owner'S Manual

Search results

Summary of Contents for IC16/8A

Reviews:

Related manuals for IC16/8A

Brands by name

Popular brands