![background image](http://html2.mh-extra.com/html/icom/id-52a/id-52a_advanced-manual_3776585208.webp)
12
SET MODE
12-29
Sounds
Volume Select
(Default: All)
[MENU] > SET > Sounds >
Volume Select
Select whether or not to adjust the audio output level
independently, according to the operating status�
• All:
The audio output level for the FM Radio,
A band (VFO A), and B band (VFO B) are
adjusted at the same time�
• FM Radio Separate:
The audio output level for the FM Radio
is independently adjusted� The audio
output level for A band (VFO A) and B
band (VFO B) are adjusted at the same
time�
• Separate: The audio output level for the FM Radio,
A band (VFO A), and B band (VFO B) are
independently adjusted�
NOTE:
When an EMR signal is received, the audio
output level for A band and/or B band may be set to
the selected level in “EMR AF Level,” depending on
this setting�
L
The audio output level for the FM Radio is not changed,
because the EMR function is for the DV mode
operation�
When “All” or “FM Radio Separate” is selected:
The audio output level for A band and B band is set
to the selected level in “EMR AF Level�”
When “Separate” is selected:
Either the audio output level for A band or B band
that the signal is received on, is set to the selected
level in “EMR AF Level�”
FM Radio Level
(Default: 0)
[MENU] > SET > Sounds >
FM Radio Level
Sets the initial audio output level difference between
the FM Radio and the A and B bands when “Volume
Select” is set to “All�”
• +5 ~ +1: The FM Radio audio output level is higher
than the VFO mode audio�
• 0:
The FM Radio audio output level is the
same as the VFO mode audio�
• –5 ~ –1: The FM Radio audio output level is lower
than the VFO mode audio�
Earphone Mode
(Default: OFF)
[MENU] > SET > Sounds >
Earphone Mode
Turns the earphone mode ON or OFF�
While in the earphone mode, the audio volume level is
automatically adjusted to the comfortable level when
the optional earphone is connected to the [MIC/SP]
jack�
Beep Level
(Default: 3)
[MENU] > SET > Sounds >
Beep Level
Sets the beep output level to 0 (OFF) or 1 (minimum)
~ 9 (maximum)�
Beep/Vol Level Link
(Default: OFF)
[MENU] > SET > Sounds >
Beep/Vol Level Link
Selects whether or not the beep output level can be
adjusted by rotating [VOL]�
• OFF: The output level is fixed to the level set in
“Beep Level�”
• ON: The output level can be adjusted by rotating
[VOL]�
Key-Touch Beep
(Default: ON)
[MENU] > SET > Sounds >
Key-Touch Beep
Turns the confirmation beep ON or OFF�
• OFF: No beep sounds�
• ON: A beep sounds when you push a key�
Home CH Beep
(Default: ON)
[MENU] > SET > Sounds >
Home CH Beep
Turns the Home CH Beep ON or OFF�
• OFF: No beep sounds�
• ON: A beep sounds when you select the Home
Channel�
L
In the VFO or Memory mode, when the Home Channel
frequency or the Home Channel Memory is selected, the
Home CH Beep sounds�
L
In the DR screen, when the Home Channel Access
repeater is set in FROM, the Home CH Beep sounds�
Band Edge Beep
(Default: OFF)
[MENU] > SET > Sounds >
Band Edge Beep
Turns the Band Edge Beep ON or OFF�
• OFF: No beep sounds�
• ON: A beep sounds when you tune out of, or back
into the AIR, VHF, and UHF band’s frequency
range�
Scan Stop Beep
(Default: OFF)
[MENU] > SET > Sounds >
Scan Stop Beep
Turns the Scan Stop Beep ON or OFF�
• OFF: No beep sounds�
• ON: A beep sounds when a scan stops by
receiving a signal�