IBM LS20 - BladeCenter - 8850 Page 89 Service Manual Download

Page: 89 / 116

To install a replacement standard-form-factor expansion card, complete the
following steps.

Expansion card

Expansion
card tray

PRESS HERE

WHEN

INST

ALLING CARD

1. If the expansion card tray was removed, secure the tray to the system board

with the screws from the option kit or from the removed drive tray.

2. Orient the expansion card and slide the notch in the narrow end of the card into

the raised hook on the tray; then, gently pivot the wide end of the card into the
expansion card connectors.

3. Install the blade server cover (see “Operating the blade server cover” on page

64 for instructions).

4. Install the blade server into the BladeCenter unit. See “Removing and installing

the blade server in a BladeCenter unit” on page 61 for instructions.

Chapter 4. Removing and replacing blade server components

Summary of Contents for LS20 - BladeCenter - 8850





















































































































Search results

Summary of Contents for LS20 - BladeCenter - 8850

Reviews:

Related manuals for LS20 - BladeCenter - 8850

Brands by name

Popular brands

IBM LS20 - BladeCenter - 8850, Service Manual

Search results

Summary of Contents for LS20 - BladeCenter - 8850

Reviews:

Related manuals for LS20 - BladeCenter - 8850

Brands by name

Popular brands