IBM 3746-900 Installation Manual Download Page 202

Page: 202 / 276

3746-900 Attached to a 3745-17A Ground Bracket Installation

Installing the Controller Expansion Ground Brackets

Step

1. ____ If installed, remove the two covers

.4/

by loosing their mounting

screws.

Step

2. ____ Install the right and left brackets

.1/

(PN 58G5676) using screws

(PN 2665527).
Before securing the ground plate screws, push down on the plate to give
it maximum contact with the floor.

Step

3. ____ Install the front ground plate

.2/

(PN 58G5675) and rear ground

plate

.3/

(PN 58G5675) using screws (PN 2665527) then re-installed

covers

.4/

Figure 10-3. Controller Expansion Ground Brackets (Front View)

Go to Chapter 11, “Making the Machine Ready for the Customer” on
page 11-1 .

10-4

3746-900: Installation Guide

Summary of Contents for 3746-900





















































































































































































































































































Search results

Summary of Contents for 3746-900

Reviews:

IBM 3746-900, Installation Manual, Page: 202 / 276

Search results

Summary of Contents for 3746-900

Reviews: