Hydro-Gear 310-1500 Service And Repair Manual Download Page 11 | Manualshive

Page: 11 / 48

background image

-1500/-1700 IHT

9

WARNING

Do not attempt any ser vic ing or ad-
just ments with the engine run ning.
Use extreme caution while inspecting
the drive belt assembly, and all vehicle
link age!

Follow all safety pro ce dures out lined in
the ve hi cle owner’s manual!

SECTION 3. TROU BLE SHOOT ING

In many cases problems with the IHT are not re-
lat ed to a de fec tive trans mis sion or axle, but are
caused by slip ping drive belts, par tial ly en gaged
bypass valves, and loose or dam aged control
linkages. Be sure to perform all op er a tion al
checks and adjustments outlined in Sec tion
4 be fore as sum ing the unit is mal func tion ing.
Table 2 below provides a troubleshooting check
list to help determine the cause of op er a tion al
prob lems.

Possible Cause

Table 2. Troubleshooting Checklist

Corrective Action

Refer To:

UNIT OPERATES IN ONE DI REC TION ONLY

Control linkage bent or out of ad just ment
Drive belt slipping or pulley damaged

Repair or replace linkage
Repair or replace drive belt or pulley

UNIT IS NOISY

Oil level low or contaminated oil
Excessive loading
Brake setting incorrect
Loose parts
Bypass assembly sticking
Air trapped in hydraulic system

Fill to proper level or change oil
Reduce vehicle loading
Adjust brake to proper setting
Repair or replace loose parts
Repair or replace valve or linkage
Purge hydraulic system

UNIT HAS NO/ LOW POWER

Engine RPM low
Control linkage bent or out of ad just ment
Brake setting incorrect
Drive belt slipping or pulley damaged
Oil level low or contaminated oil
Excessive loading
Bypass assembly sticking
Air trapped in hydraulic system

Adjust to correct setting
Repair or replace linkage
Adjust brake to proper setting
Repair or replace drive belt or pulley
Fill to proper level or change oil
Reduce vehicle loading
Repair or replace valve or linkage
Purge hydraulic system

UNIT OPERATING HOT

Debris buildup around transaxle
Brake setting incorrect
Cooling fan damaged
Oil level low or contaminated oil
Excessive loading
Air trapped in hydraulic system

Clean off debris
Adjust brake to proper setting
Repair or replace cooling fan
Fill to proper level or change oil
Reduce vehicle loading
Purge hydraulic system

TRANSAXLE LEAKS OIL

Damaged seals, housing, or gaskets
Air trapped in hydraulic system

Replace damaged com po nent
Purge hydraulic system

Control Linkage Repair, Page 23
Pulley Repair, Page 27

Fluid Maintenance, Page 11
Vehicle Speci

fi

cations

Brake Adjustment, Page 12
Appropriate Repair Pro ce dure
Bypass Repair, Page 22
Purging Procedure, Page 15

Vehicle Speci

fi

cations

Control Linkage Repair, Page 23
Brake Adjustment, Page 12
Pulley Repair, Page 27
Fluid Maintenance, Page 11
Vehicle Speci

fi

cations

Bypass Repair, Page 22
Purging Procedure, Page 15

Brake Adjustment, Page 12
Cooling Fan Repair, Page 27
Fluid Maintenance, Page 11
Vehicle Speci

fi

cations Purging

Procedure, Page 15

Appropriate Repair Procedure
Purging Procedure, Page 15

«
...
9
10
11
12
13
...
»

Summary of Contents for 310-1500

















































Reviews:

No comments

Related manuals for 310-1500

Brand: Octopus Pages: 24

Brand: Lenze Pages: 72

Brand: LaCie Pages: 32

Brand: Pentair Pages: 39

Pentek Intellidrive XL

Brand: Pentair Pages: 20

Brand: Becker Pages: 28

Brand: Lenze Pages: 43

T5 AUTOSHORT BHz

Brand: Simu Pages: 28

Brand: Malmbergs Pages: 8

Brand: ZF-DUOPLAN Pages: 34

Slim Line External PC Card CD-ROM

Brand: Targus Pages: 22

Brand: Parker Automation Pages: 362

Brand: KB Electronic Pages: 18

Brand: YASKAWA Pages: 378

Brand: Granite Devices Pages: 6

Brand: Granite Devices Pages: 14

Brand: Teac Pages: 211

Brand: Unitek Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands