Hydro-Gear 310-1500 Service And Repair Manual Download Page 29

Page: 29 / 48

-1500/-1700 IHT

CHARGE PUMP ASSEMBLY
(IF EQUIPPED)

Refer to Figure 21.

DISASSEMBLY

NOTE: Before disassembling, note the

orientation of the charge pump cover

(54). Scribe or mark the charge pump

cover (54) for correct orientation during

assembly.

1. Remove two screws (29) from the charge

pump cover (54), and remove the charge

pump cover (54).

2. Remove the o-ring (53) and gerotor as-

sem bly (52) from the charge pump cover

(54).

INSPECTION

1. Inspect gerotor assembly (52) and the

charge pump cov er (54) for damage or

ex ces sive wear.

ASSEMBLY

1. Install gerotor (52) onto in put shaft (12) (not

shown).

2. Install new O-ring (53) into charge pump

cov er (54).

3. Install charge pump cover (54), making sure

it is properly oriented.

4. Secure charge pump cover (54) by in stall ing

two screws (29), per Table 5, Page 16.

LOWER HOUSING/FILTER
ASSEMBLY (-1500)

Refer to Figure 22.

DISASSEMBLY

1. Remove the eleven housing screws (50) and

low er cover (51), and remove sealant from
the housing and lower cover (51).

2. Remove

lter (55) from the center section

assembly (3) (not shown).

INSPECTION

1. Inspect

lter (55), replace if necessary.

NOTE: Filter replacement is suggested.

ASSEMBLY

1. Install

lter (55) onto the center section (3)

(not shown).

2. Apply sealant (79) to lip of main housing (1).

See Figure 30, Page 39 for sealant path.

3. Secure lower cover (51) to main housing

(1) by installing the eleven housing screws
(50), reference Table 5, Page 16.

Fig ure 22. Lower Housing/Filter Assembly/ -1500

Fig ure 21. Charge Pump Assembly

REF. Part Name

1  Main Housing
29  Screw
52  Gerotor Assembly
53  O-Ring
54  Gerotor Cover

REF. Part Name

1  Main Housing
50  Screw
51  Lower Cover
55  Filter

Summary of Contents for 310-1500

















































Search results

Summary of Contents for 310-1500

Reviews:

Related manuals for 310-1500

Brands by name

Popular brands

Hydro-Gear 310-1500, Service And Repair Manual

Search results

Summary of Contents for 310-1500

Reviews:

Related manuals for 310-1500

Brands by name

Popular brands