Hydro-Gear 310-1500 Service And Repair Manual Download Page 20 | Manualshive

Page: 20 / 48

background image

18

-1500/-1700 IHT

INSPECTION

1. Inspect the brake pucks (120) for excessive

wear.

2. Replace with new if necessary.

ASSEMBLY

1. Install inner brake puck (120), and brake

disc (85).

2. Assemble the brake yoke assembly, by in-

stall ing puck plate (131), outer brake puck
(120) into brake yoke (122).

3. Position the brake yoke assembly against

the brake disc.

4. Install the upper bolt (121).

5. Install the lower bolt spacer (130), washer

(139) and bolt (132) to se cure the brake
yoke assembly (122).

6. Install brake anti-drag compression spring

(151), and two brake pins (125).

7. Install brake arm (124) onto brake yoke as-

sem bly.

8. Install washer (77), and castle nut (128).

9. Insert a (0.015”) (.381 mm) feeler gage be-

tween brake disc (85) and outer brake puck
(120). Adjust the brake by turning castle nut
(128) until it is snug but not tight against the
feeler gage. (The brake gap must be ad-
just ed to a (0.015”) (.381 mm) clearance.

10. Install cotter pin (129) to secure castle nut

(128).

11. Install brake arm bias spring (141) to brake

arm (124) and lower brake yoke assembly
bolt (132).

«
...
18
19
20
21
22
...
»

Summary of Contents for 310-1500

















































Reviews:

No comments

Related manuals for 310-1500

Brand: Parker Pages: 103

Brand: Beckhoff Pages: 109

Brand: GFA Pages: 18

Brand: Ltech Pages: 7

Brand: Yamaha Pages: 24

CRW4416E - CRW - CD-RW Drive

Brand: Yamaha Pages: 25

CRW4416S - CRW - CD-RW Drive

Brand: Yamaha Pages: 26

Brand: Yamaha Pages: 15

Brand: Yamaha Pages: 24

CRW8824FXZ - CD ROM Drive

Brand: Yamaha Pages: 44

PORTATONE KB-280

Brand: Yamaha Pages: 47

CRW8824SX - CRW 8424SX - CD-RW Drive

Brand: Yamaha Pages: 46

CRW8424SX Series

Brand: Yamaha Pages: 46

CRW8424E Series

Brand: Yamaha Pages: 46

CRW3200SX Series

Brand: Yamaha Pages: 46

CRW3200UX Series

Brand: Yamaha Pages: 48

CRW2200UX Series

Brand: Yamaha Pages: 45

CRW3200IX Series

Brand: Yamaha Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands