Hydac LVU-CD-40 Operating And Maintenance Instructions Manual Download Page 28 | Manualshive

Page: 28 / 68

background image

Unit setup/connection

LVU-CD-40

en(us)

Page 28 / 68

BeWa LVU-CD-40 4035823a en-us 2016-01-08.doc

2016-01-08

Connecting the water outlet

Connect the water outlet to a depressurized reservoir without cross-section
reduction. Reservoir height max. 1.5 m and no higher than the fluid level in
the tank.

The separated water can contain some parts of fuel.
Dispose of the water-fuel mixture in an environmentally
friendly manner.

NOTICE

Excess pressure at the water outlet

The unit will be damaged

►

Guide the water outlet into a depressurized reservoir.

Electrical connection

The filtration unit has a connector cable with a power plug.

DANGER

Exposed electric terminals in the terminal
box of the electric motor

Danger of fatal injury due to electric shock

►

Any work involving the electrical system may

only be done by a properly trained, certified
electrician.

Unwind the connector cable fully. Plug the power plug into a suitable,
earthed, protected power outlet. Match the specifications for the power
supply and frequency on the unit with the network specifications.
The filtration unit has a thermal motor protection switch to protect it from
electrical overload.

«
...
26
27
28
29
30
...
»

Summary of Contents for LVU-CD-40





































































Reviews:

No comments

Related manuals for LVU-CD-40

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: Unitary products group Pages: 28

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: Waters Pages: 250

Brand: Waters Pages: 141

Brand: Gaspardo Pages: 44

Brand: Abus Pages: 12

REBOUND DUAL ST

Brand: Össur Pages: 104

Brand: Össur Pages: 130

Heart Guardian AED

Brand: Radian Pages: 36

UltraVent XS Plus 6 2/3 E

Brand: Rational Pages: 220

Brand: Parkside Pages: 88

DSO8000E Series

Brand: Hantek Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands