Hydac LVU-CD-40 Operating And Maintenance Instructions Manual Download Page 57

Page: 57 / 68

Status LED / Causes and remedies

LVU-CD-40

en(us)

Page 57 / 68

BeWa LVU-CD-40 4035823a en-us 2016-01-08.doc

2016-01-08

Status LED

Cause(s)

Remedy

Leakage on the unit
/ filter housing

Empty the collecting pan and
eliminate the leak on the unit.

Wrong, missing, or
defective sealing
ring.

Check the sealing ring on the
filter element. Replace it if
necessary.

Collecting pan too
full.

The filter element is
insufficiently
tightened.

Tighten the filter housing
somewhat by hand.

The fluid is
dewatered.
No water has
drained from the
system in eight
hours. For this
reason, the control
reports that the fluid
is dewatered.

This is a status notification.
Remediation is not required.

The water drainage
valve has a
malfunction.
The water drainage
valve jams.

Contact HYDAC.

Summary of Contents for LVU-CD-40





































































Search results

Summary of Contents for LVU-CD-40

Reviews:

Related manuals for LVU-CD-40

Brands by name

Popular brands

Hydac LVU-CD-40, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for LVU-CD-40

Reviews:

Related manuals for LVU-CD-40

Brands by name

Popular brands