background image

Http://www.hybertone.com/en 

VP-102 / VP-202 User Manual 

  

35 

 

The basic syntax is “<

event

>:<

action

>|<

event

>:<

action

>|…”, where 

<

event

> defines the event to be matched.  A event consists of a sequence of digits.  If a 

specific digit has a limited range, use the syntax [A-B] where A and B are both digit 
(0 to 9) and B is greater than A.  The length of the input number can be limited by 
using “X” to represent each unknown digit.  If this field is omitted, it means any event. 

<

action

> defines the action to be taken on the number received and it consists of “–“ (minus), 

“+” (plus), and digits.  “-“ followed by digits means to remove the digits from the 
beginning of the number entered.  “+” followed by digits means to add the digits in 
front of the number entered. 

|

”     means or and the order of priority is from left to right. 

Note: For practical use, it should not be possible to reach the maximum length of the Dial Plan 

string. 

Examples: 
a)  Dial Plan = “010:-010” means that the number dialed out will have the first 3 digits ”010” 

removed when a number with the first digits as “010” is entered. 
a)  Number entered = “01082121234”, actual number dialed = “82121234”. 
b)  Number entered = “82121234”, actual number dialed = “82121234”. 

 

b)  Dial Plan = “1:+00” means that the number dialed out will have the “00” added in front of 

the number entered when a number with the first digit as “1” is entered,.  
a)  Number entered = “1082121234”, actual number dialed = “00182121234”. 
b)  Number entered = “82121234”, actual number dialed = “82121234”. 

 

c)  Dial Plan = “001:-001+1751” means that the number dialed out will the first 3 digits “001” 

changed to “1751” when a number with the first digits as “001” is entered. 
a)  Number entered = “00182121234”, actual number dialed = “175282121234”. 
b)  Number entered = “82121234”, actual number dialed = “82121234”. 

 

d)  Dial Plan = “XXXX:” means that the input number is limited to 4-digit long and will be 

dialed out immediately when the fourth digit is entered. 

 

e)  Dial Plan = “13XXX0” means that the input number is restricted to 11-digit long 

and the first two digits must be “13”.  When this condition is matched, the number dialed 
out will have a leading “0” added. 
a)  Number entered = “13901234567”, actual number dialed = “013901234567”. 
b)  Number entered = “12801234567”, actual number dialed = “12801234567”. 

 

f)  Dial Plan = “13[6-9]XX0” means that the input number is restricted to 11-digit 

long and the first two digits must be “13” and the third digit can be 6, 7, 8,or 9.  When this 
condition is matched, the number dialed out will have a leading “0” added. 

Summary of Contents for VP-102



















































Reviews: