Husqvarna F2303P0 Repair Manual Download

Page: 22 / 319

6 FORK, TRIPLE CLAMP

201361-10

201359-10

Unclamp the fork leg.

- Slide the outer tube down. Drain the fork oil.

- Clamp the fork leg with the axle clamp.

Guideline

I Use soft jaws.

Loosen rebound adjustment

C,.

Info

Do not use an impact wrench.

Place a container underneath as oil runs out in most

cases.

The rebound adjustment cannot be removed yet.

Press the cartridge against the spring and mount special

tool (D on the piston rod.
I Support tool (T14020) (

p. 306)

Hold nut @ and remove the rebound adjuster.
Press the cartridge against the spring and remove special

tool (D.

Remove the cartridge from the fork leg.
Unclamp the fork leg.

Remove the preload spacers and spring.

Summary of Contents for F2303P0
































































































































































































































































































































Search results

Summary of Contents for F2303P0

Reviews:

Related manuals for F2303P0

Brands by name

Popular brands

Husqvarna F2303P0, Repair Manual

Search results

Summary of Contents for F2303P0

Reviews:

Related manuals for F2303P0

Brands by name

Popular brands