Husqvarna 2009 TE 250 Workshop Manual Download | Manualshive

Page: 382 / 412

background image

S.4

Part. N. 8000 H0368 (09-2008)

FUEL INJECTION SYSTEM

H

This diagnosis software allows, besides the identification of the

malfunctions in progress, also the memorization of those that are
already occurred and that have been eliminated: for these last ones
it is possible to effect the cancellation, following the instructions of
the Operation Manual (page 29).

The ECU memorizes the number of the engine running hours (with

tolerance: + or - 1 hour) and, in the case of the first equipment, the
identification numbers of the frame (VIN) and of the engine (Engine
No.) of the motorcycle. In case of replacement, the new ECU will only
show the number of engine running hours.

NOTES

The NEUTRAL green warning light comes on ONLY when the ignition key is in
ON position and the R.H. commutator is in RUN position.

The front-rear lights and the instrument display will come on when the ignition key
is in ON position.

The functions controlled by the L.H. commutator and the rear stop light can be
selected ONLY when the engine is running.

For the fuel pump and relays check, please see on pages S.5 and S.6.

Adjust item No. 1
so that the “Feedback
correction value” is
~ 100.0 %

F

«
...
380
381
382
383
384
...
»

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 TE 250

Brand: Xenith Pages: 17

Brand: LAZER Pages: 2

Brand: R&G Pages: 24

690 Enduro R AU/GB 2014

Brand: KTM Pages: 18

Brand: Honda Pages: 41

Brand: TRS Pages: 38

Brand: IRC Pages: 2

Scorpion Exo-T520

Brand: Dennis Kirk Pages: 10

Brand: Romet Pages: 52

Brand: LAS Pages: 22

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 5

Brand: DYNATEK Pages: 2

Brand: Dynafit Pages: 21

Brand: Shark Pages: 24

Brand: RIEJU Pages: 52

Brand: APRILIA Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands