Husqvarna 2009 TE 250 Page 213 Workshop Manual Download | Manualshive

Page: 213 / 412

background image

I.23

Part. N. 8000 H0368 (09-2008)

FRONT SUSPENSION

ADJUSTMENTS

REBOUND ADJUSTMENT

The extension (or rebound) damping adjustment can be made by acting on the
adjustment screw ( R ) you can see on the upper cap of both legs.

To modify the rebound braking adjustment, always start from the “fully

closed” position (the screw is fully turned clockwise). Each screw position can

be recognized by a “click”.

• When turning the adjuster ( R ) clockwise, using a proper spanner, you will increase
the rebound hydraulic damping, making the fork slower during the rebound phase.

• When turning the adjuster ( R ) counterclockwise, using a proper spanner,
you will decrease the rebound hydraulic damping, making the fork more responsive
during the rebound phase.

WARNING
Do not force the adjustment screw (R) past its limits.

COMPRESSION ADJUSTMENT

The compression damping adjustment can be made by acting on the adjustment
screw ( C ) you can see at the bottom of both fork legs.

To modify the compression braking adjustment, always start from the “fully
closed” position (the screw is fully turned clockwise). Each screw position can

be recognized by a “click”.

• Remove the plastic cap

• When turning the adjuster ( C ) clockwise, using a proper spanner, you will increase
the compression hydraulic damping, reducing the travel made by the fork, under the
same stress.

• When turning the adjuster ( C ) counterclockwise, using a proper spanner, you will
decrease the compression hydraulic damping, making the fork softer against
ground harshness.

WARNING
Do not force the adjustment screw (C) past its limits.

• Put the plastic cap back to its seat.

STANDARD ADJUSTMENTS

Compression: 12 clicks
Extension: 12 clicks

R

C

«
...
211
212
213
214
215
...
»

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 TE 250

Nils Extreme MTW03

Brand: Abisal Pages: 21

Body Protector 4.5 Junior

Brand: Leatt Pages: 40

Brand: Nolan Pages: 80

Brand: RPS Pages: 28

Fastway PMB-01-5203

Brand: Pro Moto Billet Pages: 2

Brand: Yamaha Pages: 112

Brand: DYNATEK Pages: 8

2007 PAMPERA 125

Brand: GAS GAS Pages: 58

Brand: Barton Pages: 35

Brand: Dynajet Pages: 20

Brand: VESPA Pages: 82

Brand: Gemini Pages: 9

Brand: Cagiva Pages: 134

Brand: Cagiva Pages: 155

Brand: O'Neal Pages: 12

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands