Husqvarna 2009 TE 250 Workshop Manual Download | Manualshive

Page: 309 / 412

background image

M.39

Part. N. 8000 H0368 (09-2008)

ELECTRIC SYSTEM, DIGITAL INSTRUMENT

The instrument display shows even then informations of the “Neutral” condition
and of any possible “Malfunction” of the FUEL INJECTION SYSTEM;

this last

condition is showed with absolute priority with respect to any other
information.

NEUTRAL: if the speed is under 20 Km/h (12,5 mph), the “Neutral” condition the
instrument displays the N character before the value of the speed.

MALFUNCTION: in case of FUEL INJECTION SYSTEM malfunction on the right
side of the instrument display will be displayed the warning message “FAIL”.

TE

SMR

A

A

Instructions for the instrument setting

Upon turning on the instrument,

if the operation DID NOT already take place

,

it is necessary to set the instrument associating it with the relative motorcycle by
selection of the codes illustrated in the figures shown.
The identification codes appear on the display of the instrument at 2 second
intervals:

when the required code appears, press the button (A) on the

instrument

.

BE VERY CAREFUL WHEN SELECTING. THE OPERATION CAN ONLY

BE EXECUTED ONCE.

«
...
307
308
309
310
311
...
»

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 TE 250

Brand: Yamaha Pages: 88

Brand: Sachs Bikes Pages: 71

Brand: GAS GAS Pages: 74

Brand: GAS GAS Pages: 32

Brand: Honda Pages: 141

Brand: hepco & becker Pages: 4

Brand: KTM Power Parts Pages: 7

Brand: SCA Pages: 5

Brand: Miller Pages: 22

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 96

Brand: Shark Pages: 44

Brand: Faller Pages: 8

Brand: Cagiva Pages: 136

Brand: Cagiva Pages: 162

Brand: APRILIA Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands