Husqvarna 2009 TE 250 Workshop Manual Download | Manualshive

Page: 207 / 412

background image

I.17

Part. N. 8000 H0368 (09-2008)

FRONT SUSPENSION

8

9

0

1

1

1

2

1

• Insert the following components in the stanchion tube in this order: dust seal ( 12),
stop ring ( 11 ), oil seal ( 10 ), spring cup ( 9 ) and bottom guide bushing ( 8 ).

WARNING

Make sure the oil seal (10) is correctly oriented in a way that the hollow side
is turned towards the spring cup (9).

• Remove the adhesive tape from the end of the stanchion tube, cleaning any traces
of adhesive left on the fork.

• Insert the top guide bushing ( 39 ) by hand.

If this operation is difficult by hand, use a flat- tip screwdriver in the bushing
groove.

• Delicately introduce the stanchion tube into the slider, being very careful not to
damage the top guide bushing.

• Guide the bottom guide bushing until it comes into contact with the slider, the spring
cup and the oil seal.

• Mount the special introducer on the stanchion tube ( 5 ) and use this, by pushing
on the oil seal ( 10 ), to insert the bottom guide bushing, the spring cup and the oil
seal.

9

3

0

1

5

«
...
205
206
207
208
209
...
»

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 TE 250

Brand: Kappa Pages: 4

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: Yamaha Pages: 102

Brand: Honda Pages: 201

Brand: Ducati Pages: 128

Brand: MadStad Engineering Pages: 8

LIX9U0003740299

Brand: X-lite Pages: 116

Brand: MOTO GUZZI Pages: 266

Brand: Yamaha Pages: 390

Brand: Yamaha Pages: 468

Brand: Yamaha Pages: 364

Brand: Livall Pages: 20

Brand: Serpento Pages: 66

Brand: DYNATEK Pages: 2

Brand: Wunderlich Pages: 2

Brand: Sealey Pages: 2

Brand: Bagster Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands