manualshive.com logo in svg

Husqvarna 2009 TE 250, Workshop Manual

Share
Download
Husqvarna 2009 TE 250 Workshop Manual Download Page 165

H.19

Part. N. H0368 (09-2008)

ENGINE REASSEMBLY

Auxiliary shaft

A

: 2nd gear aligned with shaft broaching

B

: 5th gear engaged

C

: 4th gear engaged

D

: lubricate at the assembly with MOLYKOTE G-n plus

Main shaft

Mount the bushing, the 5th gear on the bushing and after that the washer
and the circlip. The washer should be between the gear and the circlip.
Mount the 3rd gear, the circlip and the washer. Mount the 4th gear. Mount
the spacer (only for 400-450-510 cc). Mount 2nd gear.

Main shaft complete

Auxiliary shaft complete

A

: 1st gear engaged

B

:

 3rd gear engaged

C

: 2nd gear engaged

D

: 1st gear aligned with shaft broaching

E

: lubricate at the assembly with MOLYKOTE G-n plus

Auxiliary shaft

Mount the plug and the bush. Mount 2nd gear, the washer and the circlip.
Mount the 4th gear and the circlip. Mount the washer.
Fit the washer and mount the 3rd gear into the bush. Mount the washer and
the circlip. Apply “MOLYKOTE G-n plus” under 3rd gear.
Mount 5th gear and the washer. Mount the needle bearing, the 1st speed
gear and the washer.

Summary of Contents for 2009 TE 250





























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands